Works in Iron: Bridge and Roof StructuresE. & F. N. Spon, 1877 - 343 pages Describes the practical considerations which affect the choice of design relating to iron structures. Includes examples from works constructed by Andrew Handyside & Co., and a technical vocabulary. |
From inside the book
Results 1-5 of 66
Page xiv
... Length of pieces for shipment 110 Parts of girders 68 Lewis bolts 236 Parts of roofs .. 206 Lifting machinery 119 Pavement for bridge roadways 95 Lifting roof principals 237 People , weight of , on bridges 103 Lime protection against ...
... Length of pieces for shipment 110 Parts of girders 68 Lewis bolts 236 Parts of roofs .. 206 Lifting machinery 119 Pavement for bridge roadways 95 Lifting roof principals 237 People , weight of , on bridges 103 Lime protection against ...
Page 10
... and 20 tons for plates . Iron begins to elongate directly it is strained , and stretches roboth of its length for every ton strain per square inch , up to the limit of elasticity . With a strain of 10 ΙΟ Works in Iron .
... and 20 tons for plates . Iron begins to elongate directly it is strained , and stretches roboth of its length for every ton strain per square inch , up to the limit of elasticity . With a strain of 10 ΙΟ Works in Iron .
Page 11
... length . If the iron is stretched beyond this point , the rate of elongation increases , and the permanent sett com- mences , i.e. the bar will not entirely recover itself after the strain has been withdrawn . The limit of elasticity ...
... length . If the iron is stretched beyond this point , the rate of elongation increases , and the permanent sett com- mences , i.e. the bar will not entirely recover itself after the strain has been withdrawn . The limit of elasticity ...
Page 13
... lengths of 20 , 30 , and even 40 ft . , according to their section ; but , when a weight of 4 cwt . is exceeded , extra prices are charged . As seen from the foregoing figures , plates are generally dearer than ordinary bars and L irons ...
... lengths of 20 , 30 , and even 40 ft . , according to their section ; but , when a weight of 4 cwt . is exceeded , extra prices are charged . As seen from the foregoing figures , plates are generally dearer than ordinary bars and L irons ...
Page 21
... length of the spans , and , therefore , if cheapness of the superstructure were the only consideration , it would always be best to have short spans . But as that would imply multiplication of piers , it has to be considered at what ...
... length of the spans , and , therefore , if cheapness of the superstructure were the only consideration , it would always be best to have short spans . But as that would imply multiplication of piers , it has to be considered at what ...
Other editions - View all
Common terms and phrases
abutments adopted arch arched bridge asphalte bolts bottom flange bracing building caissoon carried cast iron Centimetre centre chains cofferdam concrete considerable construction corrugated cost cross girders curved cylinders deep depth derrick described diagonal diameter engineers English engraving erected excavated feet ferro flanges galvanised guy ropes Handyside hierro holes horizontal iron columns iron girders iron roofs ironwork kind laid lattice girders length longitudinal main girders main ribs manufacture masonry material metal Midland Railway moving load necessary ordinary ornamental paint pieces piers pig iron placed plate girders platform ponte Portland cement purlines rails railway bridges riveted roadway rolled roof covering roof principals ropes sash bars screw piles shape sheets shown in Fig side span spandrels square foot steel stone strength structure struts superstructure surface suspension bridges thick timber tons top flange trave trussed vertical weight wide width wrought iron zinc
Popular passages
Page 306 - CUBIC MEASURE 1728 cubic inches = 1 cubic foot 27 cubic feet = 1 cubic yard...
Page 292 - The scale is sometimes got rid of by " pickling," the iron being first dipped in dilute acid to remove the scale, and then washed in pure water. "If the trouble and expense were not a bar to its general adoption, this is the proper process for preparing wrought iron for paint, and it is exacted occasionally in very strict specifications. " But somewhat the same results may be obtained by allowing the ironwork to rust, and then scraping the scale off preparatory to painting. If some rust remains upon...
Page 161 - Ocean, the first thing which strikes us is, that, the north-east and south-east monsoons, which are found the one on the north and the other on...
Page 7 - The deflection will vary from '3 to '5 inch. ' ' There is no difficulty in getting such iron, and higher qualities can be given if necessary, breaking strains of 30 to 35 cwt. being obtainable with judicious mixtures of the best kinds of iron ; and in testing such iron it will generally be found that some of the bars will endure as much as 38 cwt.
Page 94 - The road is to have a fall from the middle to the sides of about 1 ft. in 60, and ditches are to be dug on the field-side of the fences to a depth of a few inches below the level of the road." This system, which at one time threatened to supersede every other, is calculated to form a hard and impermeable crust on the surface, thus protecting the soft earth...
Page 306 - Measure) 4 gills = 1 pint 2 pints = 1 quart 2 quarts = 1 pottle 2 pottles = 1 gallon 4 quarts = 1 gallon 2 gallons = 1 peck 4 pecks = 1 bushel 8 bushels = 1 quarter...
Page 201 - But if the abutments already exist or if for other reasons they have to be built, the curved roof, under these circumstances, in many cases, may be found cheaper and more suitable. Flat roofs are very common, especially in hot climates. The covering of these roofs rests upon beams placed in a horizontal position, or one that is nearly so. The slope given them is generally...
Page 213 - If the iron be not suff1ciently tough and ductile it will, when corrugated, crack; and though the openings may be so small as to escape cursory examination, they will, when exposed to the weather, rapidly become rusty, and render the whole sheet worthless. The...
Page 94 - ... the large stones were removed. The broken metal is then to be carefully spread over it ; and as this operation is of great importance to the future quality of the road, the metal is not to be laid on in shovelfuls to the requisite depth, but to be scattered in shovelful after shovelful, till a depth of from 6 to 10 inches, according to the quality of the road, has been obtained.
Page 195 - Fig. 6685, but with longer rafters doubly trussed. The three forms just described are marked by the absence of vertical members, and for this reason the system is not a convenient one for hipped roofs, and for those roofs also where a longitudinal bracing between the principals is required in a vertical plane.